Sled puller makes first 1/8 pass ever @ schieds

[EDP]

This was the first time we ran our sled pulling truck at the strip and with the tunning we had for sled pulling where pretty pleased with the passes that it made

Our E/T wasnt that good but the trap speed I thought was pretty good

I believe the best pass was 7.81 @ 93.7 mph we backed the Mph later on with an even 94. We dont plan on draging this truck but it was fun to make a few passes on it.

[blksmok]

Welcome to the site! :Handshake:

That's a pretty fast 1/8th for a truck not set up to race! :thumb:

[RickDLance]

Tell us about the truck Please. :)

[Josh2002cc]

I was there and he is not joking, it ran like a red headed step child.

Also nice to meet you Chad

[99sixspeed]

Would of been nice if we had a drag tune for the truck instead of the sled one.

[Josh2002cc]

Hope you do not mind Chad, I took video of your run. It is listed under my youtube account Josh2002cc, here is the link.

http://www.youtube.com/watch?v=_dv5CsiWjUw

[VABRacing]

It was nice to meet you Josh! I had a good time beating the crap out of chads truck!!
Nice video!! We were lined up against a good friend in the ford!

[Josh2002cc]

Offtopic I know, but here is a video link of Chads sled pull. Smokey in places it really shouldn't be lol

http://www.youtube.com/watch?v=rY46ywDMxso

[99sixspeed]

We had some slight exhaust problems lol

[VABRacing]

Tell us about the truck Please. :)

02 truck, Built motor by us, custom ported heads. twin cp3s, dynomite really big injectors! Custom built charger and plumbing, Suncoast Trans, duramaxdriveshaft.com driveshaft front E-locker.

Thats all i can think of off the top of my head at the moment! :D

[Josh2002cc]

Hey josh by any chance do you have video of are sled pull?

Way ahead of you! Look above :thumb:

Not bad for an ole whiney moderator huh ):h

[VABRacing]

Offtopic I know, but here is a video link of Chads sled pull. Smokey in places it really shouldn't be lol

http://www.youtube.com/watch?v=rY46ywDMxso


link no worky josh!

[99sixspeed]

Way ahead of you! Look above :thumb:

Not bad for an ole whiney moderator huh ):h

come on now at least get it to work!:idiot::thumb:

[Josh2002cc]

The link works, that is why you see the red line that says "This video is not yet processed" so be nice guys:thumb:

[NWTDIESEL]

Pretty sweet! 3-4 shift sounded alil weird. Lots of fast trucks poppin up all over!

[99sixspeed]

Pretty sweet! 3-4 shift sounded alil weird. Lots of fast trucks poppin up all over!
Buddy said the truck laid down in third then took off like mad again in fourth. Just something in the sled pull tuning.

[EDP]

Thanks for the Video Josh. It was nice to finally put a face to the moderator that loves to stir the pot.

It definetly needs some adjusments in the tunning that is for sure.

The list of things that we have done
33x12.5R16 sts's
EDP traction bars, pulling hitch and all sheilds.
EDP Fully built motor running close to stock compression
EDP Custom ported heads
Custom built 2.95 single charger to big to fit in stock location
DDP injectors with more then enough fuel
Modded CP3's
Fass Lift pumps
SoCal sled puller came
R&R rods
Mahle pistons for a 20 over hole
duramaxdirveshaft.com drive shaft
Elocker upfront
speerco intercooler out front.
this pass was made using PPE hot +2 ET hand held tuner No EFI live at this time.
We dont plan on drag racing it any more then we did. It was built to pull. We plan on making a few hooks this weekend and will keep you guys posted on how she comes along.
Thanks again for all the comments
Chad